Skip to content
logo
0

Your basket is empty

Add products and they’ll appear here.

Antal: {{item.quantity}}
Totalsumma:{{cart.totals.total_incl_vat}}
Frakt:{{cart.totals.shipping_cost}}
Att betala:{{cart.totals.total_incl_vat}}
varav moms {{cart.totals.average_vat_rate}}:{{cart.totals.vat_amount}}

Balustrade measuring guide

To choose and order a balustrade, you need to know how long each run is, where the balustrade starts and ends, and how it will be fixed.

This measuring guide helps you measure before you buy a balustrade for your deck, balcony, Juliet balcony or staircase. We go through the measurements that matter in each setting and how to record them before you order.

Always start from where the balustrade will actually be installed. The dimensions of the finished balustrade also depend on the system and fixing you choose, so check the installation conditions and the model-specific instructions before you order.

Prepare to measure before choosing your balustrade

Before you start measuring, decide where the balustrade will go and which parts of the area need measuring. A little preparation makes it easier to record the right measurements.

01

Use a tape measure

Measure carefully in millimetres (mm) and double-check every measurement. Measure on site, not just from a drawing.

02

Take photos and make a sketch

Take photos from several angles and make a simple sketch. Mark the lengths, corners, openings and other details that affect where the balustrade goes.

03

Mark the start and end points

Decide where the balustrade will start and finish. Also note any changes of direction, steps, gates and connections to walls.

04

Check the substrate

Find out what the balustrade will be fixed into, and whether it will be fixed on top of the surface, to the side or to a wall.

How to measure for a decking or patio balustrade

When you measure for a decking balustrade, start with where the balustrade will go and how long each run is. Measure each side separately and check where the balustrade starts, ends and changes direction.

  1. Measure each side separately

    Measure the length of each continuous run where the balustrade will go. If the deck has several sides or corners, write down a measurement for each part.

  2. Check the measurements at several points

    Measure the same run at several points. Deck boards, edges and walls are not always perfectly straight, so note any differences rather than relying on a single measurement.

  3. Decide on the position and fixing

    Check whether the balustrade will be fixed on top of the surface (top-mounted) or to the outside of the edge (side-mounted). The position affects where you need to measure and how much space there is for the fixings.

  4. Note corners, openings and steps

    Mark where the balustrade changes direction or is interrupted by an opening, a gate or steps. Also write down where it will meet a wall or another structure.

How to measure for a balcony or Juliet balcony

For a standard balcony balustrade, measure the runs where the balustrade will go. For a Juliet balcony, start instead from the door opening and the space for fixing on the façade. Here is how to prepare the right measurements for each.

Option 1

Measuring for a balcony balustrade

Start from the shape of the balcony and the run where the balustrade will be installed.

  • Measure each side. Write down the length of the front edge and any sides separately. Note corners and junctions.
  • Decide on the position. Check whether the balustrade will be fixed on top of the balcony slab or to the side of the edge.
  • Check the substrate. Note where the balustrade can be anchored and whether there are openings or other details to allow for.
Option 2

Measuring for a Juliet balcony

Start from the width of the door opening and the surface the balustrade will be fixed to.

  • Measure the width of the opening. Check the width at several heights and note whether the measurements differ.
  • Check the fixing. Note whether the balustrade will sit inside the opening or on the face of the façade, and what it will be anchored into.
  • Check the door. Look at which way it opens, the handle, the threshold and other details that may affect where the balustrade goes.

The measured runs and opening sizes are your starting point. Which measurements to give when you order depends on the balustrade system, the fixing method and the measuring instructions for the model you choose.

How to measure for a staircase balustrade

When you measure for a staircase balustrade, you need to allow for the pitch of the stairs, the size of the steps and where the balustrade starts and ends. Also check how it will be fixed and whether it continues onto a landing or another level surface.

  1. Mark where the balustrade will start and end

    Decide where the balustrade will start and finish. Note whether it continues onto a landing, meets a wall or runs into a balustrade on a level surface.

  2. Measure the length along the pitch of the stairs

    Measure the sloping distance between the planned start and end points, not just the horizontal distance. Write the measurement down in millimetres (mm).

  3. Check the rise, going and number of steps

    Measure the height (rise) and depth (going) of the steps and count how many there are. Check several steps so that you spot any differences. These measurements help you describe the pitch of the stairs.

  4. Decide on the position and fixing

    Note whether the balustrade will be fixed on top of the steps, to the side of the staircase or to a wall. Check the substrate and take photos of the stairs from the side and from the front.

Key measurements and details to check

Before you order, check that all measurements are clear and that nothing is missing. Use the checklist to gather the details of the balustrade’s position, fixing and design.

Before you order

Check these six points

  • Have you marked where the balustrade starts and ends?

    Mark where the balustrade will start and finish. Also check any connections to walls or other balustrade sections.

  • Have you measured each side separately?

    Write down the length of each continuous run in millimetres (mm). Double-check the measurements, especially at corners and changes of direction.

  • Have you noted openings and breaks?

    Mark steps, gates, door openings and other places where the balustrade stops or changes direction.

  • Are the position and fixing method clear?

    Note whether the balustrade will be fixed on top of the surface, to the side of an edge or to a wall. Check that the position suits the balustrade system you choose.

  • Have you checked the substrate?

    Find out what the balustrade will be anchored into and check its condition. The fixings must suit both the structure and the location.

  • Have you collected photos and a measured sketch?

    Add photos from several angles and a simple sketch seen from above. Finally, check which measurements to give for the balustrade model you have chosen.

Next step

Ready to choose your balustrade?

Once you have checked your measurements and the installation conditions, you can compare our balustrades and find one that suits your space. If you are unsure about your measurements or which balustrade to choose, our customer service team will help you.

logo

Get personal help – completely free

Select a country
Select a language

You are on the Balustradedesign United Kingdom website

Your basket will be emptied if you switch to another country.

Product Image

Environments
Products